Neil Marine

44FT DIVE EXCURSION PASSENGER TRANSPORT CATAMARAN

44FT DIVE EXCURSION PASSENGER TRANSPORT CATAMARAN

LENGTH OVER ALL

13.35M

BEAM OVER HULL

4.70M

DRAUGHT(LADEN)

0.975M

DISPLACEMENT(LADEN)

9.9TONS

FUEL CAPACITY (PETROL)

750L

FUEL CAPACITY (DIESEL)

250L

BLACK WATER CAPACITY

150L

WATER CAPACITY

500L

SEATING CAPACITY

20 

SPEED MAX

18-20 KNOTS

PROPULSION

TWIN MERCURY VERADO 200HP 4-STROKE OBM ENGINES

GENERATOR

CATERPILLAR C1.5,12KW MARINE DIESEL

PART ASSEMBLY

Deck

As Shown in the G.A Drawing deck fittings are fitted and railing fitted right around. The side-walk and fore-deck along with the fly-bridge floor has been laid with Ceylon teak. The floor aft of the cockpit has a non skid finish. Loop pile carpet has been used to cover the floor inside the cockpit. The galley floor has been laid with Ceylon teak.

Wheelhouse

Cockpit Area

Helm position and console is provided to front centre with steering wheel, engine controls and instrumentation within easy reach of the helmsman. A 24000BTU Marvair air-conditioner has been fitted inside the cockpit with vents. Lounge seats have been provided on both PORT and STBD sides with a fibreglass table which when lowered acts as a base when converting the seats into beds. The ceiling inside the cockpit has been covered using Vinyl fabric.

Aft. Cockpit Area

Fiberglass cushion seats with back rests have been provided on both PORT and STBD sides. Compartments have been provided below the seats to store 40 scuba tanks. The staircase has been placed on the STBD side and a fibreglass compartment has been made for the air compressor used to fill the scuba tanks. Hatches have been placed to enter the fuel tank compartments, generator compartment and the battery compartment. Fuel fillers and water fillers have been placed on the side walk.

Fly Bridge

The fly bridge consists of a U-shaped couch and a table along with sink, tap a Barbeque grill and a Mini fridge. The Barbeque grill is placed inside a compartment which can be locked. The grill is placed on a stand which can be lifted or lowered to meet with the safety requirements set by the grill manufacturers. A console will be provided on the upper deck for control of the boat in the center forward area of the fly-bridge. Entry to the upper deck will be through a U shaped staircase which will be located in the STBD side of the boat in the mid-ship area.

Toilet

Fully functional western style toilet has been provided with a sink, tap and a pull out shower. The toilet is located in the forward section of the boat on the STBD side. Entry to the Toilet will be through a staircase in the forward section of the wheel house

Galley

The galley is located in the forward section of the boat on the port side. Entry to the Galley will be through a staircase in the forward section of the wheel house. The galley will consist of Gas Stove, counter top and sink. The Mini fridge is located below the counter top

 EXTERIOR FIT OUT

Mooring Equipment
  • 10” cleats will be placed on PORT and STBD sides on Fore Deck and Aft Deck. Total 4 No’s have been provided.
  • 4 Units Stainless steel mooring bollards have been fitted on PORT and STBD sides on Fore and Aft Deck as shown in General Arrangement Drawing.
  • Kobra 900Kg Max Pull Capacity with Hauling speed of 20Kg/min (50Kg load) Including a 2-way relay, fuse and breaker along with 2 station control (foot switches on fore deck and Main Console inside the wheel house) along with a stainless steel bow roller and 15kg galvanized steel anchor have been fitted on the fore deck.
  • Additional 15Kg Galvanized Steel Anchor has been provided.
  • 8mm Galvanized Steel short link chain (31 Mtrs) provided.
  • 14mm P.P. Rope 30m Long has been provided.
  • 2 Units 18mm Mooring Rope 10m long have been provided.
Fender
  • Heavy duty “D” type rubber fender to fit around the gunwale. 5 inflatable rubber fenders have been provided.

GENERAL ARRANGEMENT

Deck

As Shown in the G.A Drawing deck fittings are fitted and railing fitted right around. The side-walk and fore-deck along with the fly-bridge floor has been laid with Ceylon teak. The floor aft of the cockpit has a non skid finish. Loop pile carpet has been used to cover the floor inside the cockpit. The galley floor has been laid with Ceylon teak.

Wheelhouse
Cockpit Area

Helm position and console is provided to front centre with steering wheel, engine controls and instrumentation within easy reach of the helmsman. A 24000BTU Marvair air-conditioner has been fitted inside the cockpit with vents. Lounge seats have been provided on both PORT and STBD sides with a fibreglass table which when lowered acts as a base when converting the seats into beds. The ceiling inside the cockpit has been covered using Vinyl fabric.

Aft. Cockpit Area

Fiberglass cushion seats with back rests have been provided on both PORT and STBD sides. Compartments have been provided below the seats to store 40 scuba tanks. The staircase has been placed on the STBD side and a fibreglass compartment has been made for the air compressor used to fill the scuba tanks. Hatches have been placed to enter the fuel tank compartments, generator compartment and the battery compartment. Fuel fillers and water fillers have been placed on the side walk.

Fly Bridge

The fly bridge consists of a U-shaped couch and a table along with sink, tap a Barbeque grill and a Mini fridge. The Barbeque grill is placed inside a compartment which can be locked. The grill is placed on a stand which can be lifted or lowered to meet with the safety requirements set by the grill manufacturers. A console will be provided on the upper deck for control of the boat in the center forward area of the fly-bridge. Entry to the upper deck will be through a U shaped staircase which will be located in the STBD side of the boat in the mid-ship area.

Toilet

Fully functional western style toilet has been provided with a sink, tap and a pull out shower. The toilet is located in the forward section of the boat on the STBD side. Entry to the Toilet will be through a staircase in the forward section of the wheel house

3.5 Galley

The galley is located in the forward section of the boat on the port side. Entry to the Galley will be through a staircase in the forward section of the wheel house. The galley will consist of Gas Stove, counter top and sink. The Mini fridge is located below the counter top.

ELECTRICAL

Electrical system

12V DC system with following navigational lights and standard lighting. a. Remote control Search light b. Battery charger with shore power connection. Wiper Three No’s to Fit on Helm screen

Batteries

4 Batteries will be provided.

Type  – 12 volt x 200 Amp-hr lead acid type – 3 Units

12 volt X 90 Amp-hr lead acid type – 1 Unit

Batteries are to be charged by alternator and battery charger. Battery charger will be provided to charge the batteries by shore supply when vessel is berthed and by Generator when the vessel is at sea. 

Navigational Lights and equipment

1 No Port

1 No Starboard

1 No Stern

1 No Mast Head Light

1 No Anchor Light Port and starboard lights mounted on fwd deck. Stern light will be mounted on aft of the deck. Compass 3 ½” Card Dia. 1 No

Garmin GPS (Optional) 1 No

Bulk Head Lights 13 No’s

PLUMBING SYSTEM

Bilge System  Bilge Pumps  No   8  

Type  12V electric submersible bilge pumps of 1500 Gls/per Hr. are fitted all water tight compartments.

With separate discharge ports  

 

ENGINE / STEERING

Propulsion        

2 X 200 HP 4 STROKE Mercury Verado OBM                                   

Steering

Manual Hydraulic steering system fitted with wheel at Console on deck and fly-bridge as with standard   controls.

LIFE SAVING AND SAFETY EQUIPMENT 

Life Ring 75 mm Outer Diameter 04 No’s Life Jackets for Adults 24 No’s First Aid Locker (Optional) 01 No

FIRE FIGTHING EQUIPMENT

Fire Extinguishers                             06 No’s

Make fire master (BSEN3”1996)

MATERIAL AND WORKMAN SHIP   

All materials, and equipment used are of marine type and suitable for the intended services and to be free of imperfections of manufacture and defects. All fibre glass material used is of best quality material and approved by Lloyds Register of shipping. All fasteners used for construction and assembly of the launch to be stainless steel and brass and where necessary to be galvanized steel. 

Painting and Finishing

The vessel will be painted by gelcoating method. Under water areas will be painted with approved quality antifouling. The hull and deck colours will be as per customer requirement and subject to availability. All stainless steel fittings are polished Furniture joinery work where varnished is to be given not less than 3 coats. All trims will be out of teak trims.

TRIALS AND WARRANTY

Trials The craft will be launched and trialled in the presence of the owner’s representatives on board. Warranty The Builder will guarantee the vessel for a period of one year commencing from the date of handing over arising from any workmanship or material defects. All equipment and machinery will carry manufacturer’s warranty.

YOU MAY ALSO LIKE